- CrystalDiskInfo says my drive is not OK! - Internal Hardware.
- Crystaldisk info explanation | AnandTech Forums: Technology, Hardware.
- Interpreting the Spin Retry Count S.M.A.R.T. attribute value for hard.
- HDD Spin retry count: non-zero values | TechPowerUp Forums.
- CrystalDiskInfo HDD Spin Retry Count failed (red) - reddit.
- Hard Disk Failure! Crystaldiskinfo Reports BAD Health.
- [Solved] "Raw Read Error Rate" in Drive.
- Calibration Retry Count error on HDD? - Linus Tech Tips.
- Solved: Uh Oh! Uncorrectable Sector Count Warning here.
- SMART values and there meaning HDD diskinfo | QNAP (US).
- HDD might be failing? Not sure what the CrystalDiskInfo results mean.
- Caution On 2 Drives found with CrystalDiskinfo | guru3D Forums.
- Spin Retry count, End to End Error rate | Tom's Hardware Forum.
CrystalDiskInfo says my drive is not OK! - Internal Hardware.
Spin Retry Count Disk Temperature Moreover, CrystalDiskInfo is really great which is giving you a good peak at your drive. It also allows you to make judgement on when you need to check your disk for any errors in the near future. This disk comes with an S.M.A.R.T pack.
Crystaldisk info explanation | AnandTech Forums: Technology, Hardware.
I've just run a check on my drives and CrystalDiskInfo says that the health status of my Seagate Barracuda 4tb is 'bad' (see image). The only failing attribute is the 'spin retry count'. Will this mean that my hard drive WILL die soon? even though all of the other attributes are green and good?.
Interpreting the Spin Retry Count S.M.A.R.T. attribute value for hard.
Apparently he asked me to run a hard disk test using CrystalDiskInfo. I did, and CrystalDiskInfo said that my drive is not OK, but instead, the drive status is caution. I think this is the right. 0A 206 100 _30 000000000000 Spin Retry Count 0C 100 100 __0 0000000014A4 Power Cycle Count... DF 100 100 __0 000000000000 Load/Unload Retry Count E0 100 100 __0 000000000000 Load Friction... Crystaldiskinfo is not showing "caution" on any attributes so i will keep this HDD until I save some money for SSD. Temperature is now lower. It was 49. I downloaded CrystalDiskInfo, and the pertinent information is reproduced below: In short, the Uncorrectable Sector Count count is 100, and this is a "caution"-level problem on the drive.... Interpreting the Spin Retry Count S.M.A.R.T. attribute value for hard drives ; Initial Testing of New Hard Drives in Linux ; Post navigation.
HDD Spin retry count: non-zero values | TechPowerUp Forums.
C0 200 200 __0 000000000147 Power-off Retract Count C1 _83 _83 __0 0000000561E8 Load/Unload Cycle Count C2 102 _87 __0 000000000029 Temperature C4 192 192 __0 000000000008 Reallocation Event Count C5 200 200 __0 000000000000 Current Pending Sector Count C6 100 253 __0 000000000000 Uncorrectable Sector Count. Spin Retry Count:The counter that logs how many times the motor has had to start for the disk to reach its typical operating speed. Recalibration Retries:The number of recalibrations of the read/write head. Indicates a mechanical malfunction. Reallocation Events Count:Logs every attempt to move sectors. The report is fine. The SMART metrics use high values as good and low values as bad. That means if the metric falls below the threshold then that indicates there is a problem. The worst values just indicate the lowest values ever seen. So for most of your attributes the lowest value ever seen was 100, which is a perfect score.
CrystalDiskInfo HDD Spin Retry Count failed (red) - reddit.
I just recently ran CrystalDiskInfo and it said that my hard disk health status is "Caution". I also recently updated my laptop to Windows 8.1 from Windows 8 and that's when I felt my laptop got slower.... 0A 100 100 _60 000000000000 Spin Retry Count 0C _98 _98 __0 000000000EBA Power Cycle Count B7 100 100 __0 000000000000 Vendor Specific B8. Just noticed my external HDD shows up having a Calibration Retry Count error, and the Data value is 5. According to Crystaldisk, it also reads 5 under Data, but Recalibration Retries is blue instead of yellow (meaning it's normal) and my health status is Good. I have no idea what this means, only that potentially it could be a problem.
Hard Disk Failure! Crystaldiskinfo Reports BAD Health.
(03) Spin Up Time 154 151 21 1291 ok 6. (04) Start/Stop Count 97 97 0 3211 ok 7. (05) Reallocated Sector Count 200 200 140 0 ok 8. (07) Seek Error Rate 100 253 0 0 ok 9. (09) Power On Hours Count 94 94 0 4860 ok 10. (0A) Spin Retry Count 100 100 0 0 ok 11. (0B) Calibration Retry Count 100 100 0 0 ok 12. (0C) Power Cycle Count 97 97 0 3157 ok 13. So usually the value of 100 means that everything is OK. Higher values often mean that the attribute has never been updated (implies 100). As your Current value is 166, this only means that you never had a Spin Retry Count error, which agrees with your Raw value of 0. You should consider replacing the disk if Current ever drops below 30.
[Solved] "Raw Read Error Rate" in Drive.
I've been worried about the current threshold of my main hard drive Seagate (ST3250318aS - 250.0 GB) with his current Attribute of - Spin Retry count. Step 5: Turn on 'Deep Scan' toggle switch at bottom left and click 'Scan.' Step 6: After the scan, the recovered files are listed in the left Tree View pane. Expand the tree to see files. So I recently got my hard drive replaced under warranty as CrystalDiskInfo said it's health was bad and the spin retry count was bad. All of a sudden I started hearing a clicking noise again and open up CDI. Spin retry count is bad it says (at 88). Now today it's dropped to 86. What should I do? Both hard drives were seagate barracuda 2TB HDD.
Calibration Retry Count error on HDD? - Linus Tech Tips.
My laptop has been acting up (general performance issues) lately so I ran a Crystal Disk Info check and it came up with a warning: Reallocated sectors count Current pending sector count Uncorrectable sector count are all yellow. I've attached a Ctrl+C of the window below but the screenshot attached might be more useful. More importantly, other significant counts are zero- seek error rate (this'll be a positive figure if theres a mechanical positioning problem or a thermal widening of the platters), the spin retry count (number of attemts to reach full speed), the current pending sector count ( number of unstable sectors waiting to be mapped) and the.
Solved: Uh Oh! Uncorrectable Sector Count Warning here.
CrystalDiskInfo HDD Spin Retry Count failed (red) - reddit. SMART Reallocated Sector Count 269, Reallocated Event Count 20. Maximum values are typically 100, 200 or 253. Rule of thumb is: high values are good, low values are bad. " Threshold " - the minimum normalized value limit for the attribute.
SMART values and there meaning HDD diskinfo | QNAP (US).
This warns of detected problems with the disk hardware. chkdsk is a Windows utility which checks for any problems in the NTFS or FAT file system - it will not necessarily detect hardware problems. Spin Retry Count: 100: 100: 0: 000000000000: 0B: Recalibration Retries: 100: 100: 0: 000000000000: 0C: Power Cycle Count: 96: 96: 0: 000000000FE1: C0: Power-off Retract Count: 200: 200: 0:... If you think CrystalDiskInfo is also basic, you may want to consider SeaTools from Seagate (for its drives), Data Lifeguard Diagnostic from Western. Use crystaldisk info to check, mine reports all zero's for an hdd with 11k hours on it. Spin retry could mean the motor is going and you should backup data. Shrek Joined Mar 21, 2021 Messages 2,131 (4.69/day) Location Colorado, U.S.A. System Specs Apr 24, 2022 #6 80251 said.
HDD might be failing? Not sure what the CrystalDiskInfo results mean.
Caution On 2 Drives found with CrystalDiskinfo. Discussion in 'SSD and HDD storage' started by AMDMan2016, Feb 2, 2020. AMDMan2016 Active Member. Messages: 84... 0A 100 100 _60 000000000000 Spin Retry Count 0C _99 _99 __0 00000000135E Power Cycle Count B7 100 100 __0 000000000000 Vendor Specific. CrystalDiskInfo. a guest. May 14th, 2017. 252. Never... 0A 100 100 _50 000000000000 Spin Retry Count 0C 100 100 __0 0000000003BF Power Cycle Count... C4 100 100 __0 000000000000 Later Bad Block Count C5 100 100 __0 000000000000 Current Pending Sector Count. I added Airflow Temperature (Attribute ID 0xBE) support in CrystalDiskInfo 3.9.4. Please test and report it.
Caution On 2 Drives found with CrystalDiskinfo | guru3D Forums.
Spin retry count: Spin retry event is logged each time the drive was unable to spin its platters up to the rated rotation speed in the due time. Spin-up attempt was aborted and retried. This typically indicates severe controller or bearing problem, but may be sometimes caused by power supply problems. Drive lifetime information: Drive start. Is spin retry count represent an aggregate value (i.e. of all spin retries for the life of the HDD) or a worst case event. Maximum values are typically 100, 200 or 253. Rule of thumb is: high values are good, low values are bad. " Threshold " - the minimum normalized value limit for the attribute. So I got CrystalDiskInfo and ran it, turns out my external is fine, but my main drive, C:, has Caution. Im not entirely sure what that means, I dont see anything explaining it. Here is the copied bit.... 0A 100 100 __0 000000000000 Spin Retry Count 0B 100 253 __0 000000000000 Recalibration Retries 0C 100 100 __0 000000000032 Power Cycle Count.
Spin Retry count, End to End Error rate | Tom's Hardware Forum.
So usually the value of 100 means that everything is OK.Higher values often mean that the attribute has never been updated (implies 100). As your Current value is 166, this only means that you never had aSpin Retry Count error, which agrees with your Raw value of 0.You should consider replacing the disk if Current ever drops below 30.
Other content: